Christine Cox

Posts tagged ‘silver’

Metalsmith: Mandrel for Tiny Jump Rings


Mandrel for Tiny Jump Rings
(A typically occasional metalsmithing series by Christine Cox)

Use a piece of steel tie wire as a mandrel when making tiny jump rings. It doesn’t bend as much as copper, nickel-silver or brass so it’s a lot easier to wrap the jump ring wire around it. I like to capture both the tie wire and the jump ring wire in a small vise and then use a pair of flatnose pliers and my fingers to manipulate the jump ring wire around the tie wire.

Advertisements

Metalsmith: Kitchen Tools in the Studio

Metalsmith
(A typically occasional series by Christine Cox)

The sweeps drawer under my bench used to be a mess. I had tools mixed in with metal scrap, used sandpaper, leather pieces, broken saw blades, and lots and lots of metal shavings from sawing and filing. It was a major undertaking to clean it and a job I avoided. At a local store I found a metal mesh drawer organizer. Now my tools all have individual homes and all I do to clean up the drawer is to lift the organizer out, dump out the sweeps and put the organizer back in. The mesh organizer is a great holder for my most-used tools too.

Silverware holders are also wonderful for organizing tools in drawers. Mandrels, sanding sticks and other hand tools will stay in their assigned slots without beating up their neighbors.

Metalsmith: Triangles and Squares

Metalsmith: Triangles and Squares
(another installment in a typically occasional series by Christine Cox)

templateA fast way to accurately mark 3 or 4 corners on a piece of work is to use a drafter’s template. For example, let’s say you want to put 3 tiny feet on the bottom of a round box. It can be difficult to line up 3 points that look good. Simply lay a triangle template over the bottom of the box and then find the triangle that is closest in size to where you want the feet. Mark the 3 corners with a Sharpie marker and you’re done. If you want the feet in a perfect square instead, simply use whichever square template is the correct size.

2012-05-2in

Bookbinding, Metalsmithing and Stained Glass

 

 

Metalsmith: Twist to De-Bur

Metalsmith: Twist to De-Bur
(another installment in a typically occasional series by Christine Cox)removebur-done

After drilling in metal there is often a large bur around the hole. It’s unsightly, dangerous and can throw off how your piece goes together. Eliminate it easily by using a drill bit that’s larger (by far) than the hole you’ve drilled. Chuck the large bit up into a pin vise. Place the metal, bur side up, onto a surface that allows the tip of the drill bit to drop down through the hole. I usually just place the hole over the V in my bench pin, or slide it off the edge of the bench, whichever is easiest. Press down firmly and twist to remove the bur. Caution, don’t go all the way through or you’ll be left with a hole much larger than you intended. Lightly twist back and forth a couple of additional times to clear the swarf and you’re done.

This is also a quick and dirty way to create a countersunk hole. Just push down a little harder as you twist to get the characteristic flared out edge around the hole.

removebur  removebur-dtl

Available from Volcano Arts:


Metal stock


Small pin vise

Metalsmith: Filing in Tight Places

barrettefilebarrette

Metalsmith
(A typically occasional series by Christine Cox)

For filing in tight places where adjoining areas could be damaged, use a barrette file. Only one side has teeth and the other edges slope away from them. They come in several sizes and every coarseness you could need. They are even included in most needle file and mini-needle file sets.

Needle and mini-needle file sets are available from Volcano Arts
showme

Metalsmith: Graphite for Alignment

graphitesoldering

Metalsmith
(A typically occasional series by Christine Cox)

When soldering a pin back onto a brooch, use a piece of graphite (you know, for mechanical pencils) to ensure that catch and joint are lined up. The graphite will take the heat of your torch while your pin back stays straight.

Bird brooch available in my Etsy store

Metalsmith: Sternum Pain Deliverance

leatheronapron

Metalsmith
(A typically occasional series by Christine Cox)

While stringing a saw frame most people use their sternum to compress the frame while tightening. This can be dangerous and painful if you have bird bones like mine. Staple a piece of leather to your shop apron and you’ll have some protection.

 

Tag Cloud